3CX 15 SIP Trunk
This is a step-by-step procedure to setup a Simtex SIP trunk with 3CX version 15.
Our guide assumes you have already set the server up, and have the web-based GUI up and running.
This is a step-by-step procedure to setup a Simtex SIP trunk with 3CX version 15.
Our guide assumes you have already set the server up, and have the web-based GUI up and running.
1 | Adding a New Sip Trunk | |||||||||||||||||||||||||
Click Trunk on the left main menu then add SIP trunk | ||||||||||||||||||||||||||
![]() |
||||||||||||||||||||||||||
2 | Add SIP trunk/VoIP provider | |||||||||||||||||||||||||
Enter Generic Country, Generic VoIP Provider and the Primary number | ||||||||||||||||||||||||||
![]() |
||||||||||||||||||||||||||
3 | Generic VoIP provider: | |||||||||||||||||||||||||
Trunk Details: | ||||||||||||||||||||||||||
Registrar/Server/Gateway Hostname or IP: Enter sip.simtex.com.au | ||||||||||||||||||||||||||
Number of SIM calls: Total number of combined inbound and outbound Simtex channels | ||||||||||||||||||||||||||
Authentication: | ||||||||||||||||||||||||||
Type of Authentication: Register/Account based | ||||||||||||||||||||||||||
Authentication ID: Your Simtex account number, eg 711111111 | ||||||||||||||||||||||||||
Authentication Password:Your Simtex password or PIN | ||||||||||||||||||||||||||
![]() |
||||||||||||||||||||||||||
4 | Routing of calls to Main Number: | |||||||||||||||||||||||||
Main Trunk No: Your primary inbound number, starting with 61 | ||||||||||||||||||||||||||
![]() |
||||||||||||||||||||||||||
5 | Creating a Extension: | |||||||||||||||||||||||||
1. Click Extensions on the left main menu. | ||||||||||||||||||||||||||
2. Select “Add” | ||||||||||||||||||||||||||
3. Fill in the Use Information | ||||||||||||||||||||||||||
![]() |
||||||||||||||||||||||||||
6 | Creating a Ring Group: | |||||||||||||||||||||||||
Click RingGroup on the left main menu. | ||||||||||||||||||||||||||
1. Select “Add Ring Group” | ||||||||||||||||||||||||||
2. Under General
|
||||||||||||||||||||||||||
3. For Group Members select extensions to be apart of that group | ||||||||||||||||||||||||||
7 | Out Bound Routes | |||||||||||||||||||||||||
Note: You will need to setup outbound rules for each destination you would like to have your system call. | ||||||||||||||||||||||||||
Click Outbound Rules on the left hand side then select add. | ||||||||||||||||||||||||||
Rule Name: Label your entry | ||||||||||||||||||||||||||
Calls to numbers starting with prefix: Enter the starting digits of the numbers you would like to call | ||||||||||||||||||||||||||
Calls to Numbers with a length of: Length of number | ||||||||||||||||||||||||||
An example configuration for Australia | ||||||||||||||||||||||||||
|
||||||||||||||||||||||||||
[alert]Note: You will need a separate rule entry for each destination[/alert] | ||||||||||||||||||||||||||
![]() |
||||||||||||||||||||||||||
8 | Adding Inbound Routes | |||||||||||||||||||||||||
Click Inbound Rules on the left menu | ||||||||||||||||||||||||||
[alert]Note: You will need to determine if you want calls to route to an extension or to a ring group.[/alert] | ||||||||||||||||||||||||||
![]() |
||||||||||||||||||||||||||
1. Click On Add DID rule, note that there will need to be DID’s listed under the trunk properties | ||||||||||||||||||||||||||
2. Enter the Name of the route | ||||||||||||||||||||||||||
3. determine the routing of the calls for during office hours and outside of. | ||||||||||||||||||||||||||
![]() |
||||||||||||||||||||||||||
To have Calls Route to a ring group use the following setting: | ||||||||||||||||||||||||||
![]() |